PRECIPITATION OF CUAL₂ (THETA ') DURING ORTHOGONAL CUTTING OF AL-4CU ALLOY = PRECIPITATION DE CUAL₂ (THETA ') PENDANT LA COUPE ORTHOGONALE DE L'ALLIAGE AL-CUBLACKBURN RL; GREGORY B.1975; METALS TECHNOL.; G.B.; DA. 1975; VOL. 2; NO 9; PP. 438-443; ABS. ALLEM. FR.; BIBL. 13 REF.Article

THE RANGE OF PERMISSIBLE SHEAR ANGLES IN ORTHOGONAL MACHINING ALLOWING FOR VARIABLE HYDROSTATIC STRESS ON THE SHEAR PLANE AND VARIABLE FRICTION ANGLE ALONG THE RAKE FACEROTH RN.1975; INTERNATION. J. MACH. TOOL DESIGN RES.; U.S.A.; DA. 1975; VOL. 15; NO 3; PP. 161-177; BIBL. 13 REF.Article

DETERMINAZIONE DEI COEFFICIENTI DINAMICI DI TAGLIO ATTRAVERSO PROVO DI TAGLIO STATICO = EVALUATION DES COEFFICIENTS DYNAMIQUES DE COUPE A PARTIR D'ESSAIS DE COUPE EN REGIME STATIONNAIREGRASSO V; LA DIEGA SN; PIACENTINI M et al.1977; TEC. ITAL.; ITA; DA. 1977; VOL. 42; NO 2; PP. 71-77; ABS. ENG; BIBL. 17 REF.Article

A STUDY OF THE ORTHOGONAL CUTTING MECHANISM BY CONTROLLED SHEAR ANGLE EXPERIMENTSAKIYAMA T; KISHINAMI T; SAITO K et al.1975; MEM. FAC. ENGNG, HOKKAIDO UNIV.; JAP.; DA. 1975; VOL. 14; NO 1; PP. 13-20; BIBL. 1 REF.Article

THE EFFECT OF RAKE FACE CONFIGURATION ON THE CURVATURE OF THE CHIP IN METAL CUTTING = EFFET DE LA FORME DE LA SURFACE D'ATTAQUE SUR LA COURBURE DE COPEAU LORS DE LA COUPE DES METAUXWORTHINGTON B.1975; INTERNATION. J. MACH. TOOL DESIGN RES.; U.S.A.; DA. 1975; VOL. 15; NO 4; PP. 223-239; BIBL. 9 REF.Article

LE COPEAU D'USINAGE AUX TRES FAIBLES VITESSESREGORD C.1975; AO-CNRS-11579; FR.; DA. 1975; PP. (280 P.); H.T. 3; BIBL. 2 P. 1/2; (THESE DOCT. SCI. PHYS.; UNIV. SCI. TECH. LANGUEDOC)Thesis

UN NOUVEAU DISPOSITIF DE COUPE BRUSQUEMENT INTERROMPUEFURRER JC; DINICHERT P.1975; MEC. MATER. ELECTR.; FR.; DA. 1975; NO 303; PP. 28-32; BIBL. 30 REF.Article

BUILT-UP EDGE FORMATION IN MACHININGSTEVENSON MG.1976; J. AUSTRAL. INST. METALS; AUSTRAL.; DA. 1976; VOL. 21; NO 1; PP. 16-23; BIBL. 20 REF.Article

USING THE FINITE ELEMENT METHOD TO DETERMINE TEMPERATURE DISTRIBUTIONS IN ORTHOGONAL MACHINING = UTILISATION DE LA METHODE DES ELEMENTS FINIS POUR DETERMINER LA DISTRIBUTION DES TEMPERATURES EN COUPE ORTHOGONALETAY AO; STEVENSON MG; DE VAHL DAVIS G et al.1974; INSTIT. MECH. ENGRS, PROC.; G.B.; DA. 1974; VOL. 188; NO 55; PP. 627-638; BIBL. 19 REF.Article

ETUDE PHOTOELASTIQUE DE LA COUPE ORTHOGONALE DE L'ALUMINIUMZAIMA S; SUZUKI Y; YAMASHITA M et al.1974; J. JAP. INST. METALS; JAP.; DA. 1974; VOL. 38; NO 7; PP. 615-620; ABS. ANGL.; BIBL. 7 REF.Article

SHEAR ANGLE RELATIONSHIP WITH VARIABLE UNDEFORMED CHIP THICKNESSKAINTH GS; GUPTA RC.1974; J. ENGNG INDUSTRY; U.S.A.; DA. 1974; VOL. 96; NO 4; PP. 1272-1276; BIBL. 10 REF.Article

THE EFFECTS OF ANISOTROPY ON THE CUTTING MECHANISM OF 5083 ALLOYSAGA T; NAGAI S.1980; NIPPON KINZOKU GAKKAISHI (1952); ISSN 0021-4876; JPN; DA. 1980; VOL. 44; NO 6; PP. 589-593; ABS. ENG; BIBL. 9 REF.Article

TWO NEW MODELS FOR ORTHOGONAL CHIP FORMATIONANAND JR; SEKHON GS; SACHDEV AS et al.1979; J. INSTIT. ENGRS (INDIA), MECH. ENGNG DIV.; IND; DA. 1979; VOL. 59; NO 6; PP. 300-306; BIBL. 5 REF.Article

APPLICATION OF DIMENSIONAL ANALYSIS TO THE DETERMINATION OF PRIMARY SHEAR DEFORMATION ZONE SIZEJAIN VK; GARG SBL.1978; J. INSTIT. ENGRS (INDIA), MECH. ENGNG DIV.; IND; DA. 1978; VOL. 59; NO 2; PP. 70-74; BIBL. 20 REF.Article

STUDIES ON CUTTING MECHANISM OF ALUMINIUM SINGLE CRYSTALSATO M; KATO Y; TUTIYA K et al.1979; J. JAP. INST. LIGHT METALS; JPN; DA. 1979; VOL. 29; NO 1; PP. 3-8; ABS. ENG; BIBL. 5 REF.Article

EXPERIMENTAL INVESTIGATION OF THE CHARACTERISTICS OF DYNAMIC CUTTING PROCESS.NIGM MM; SADEK MM.1977; J. ENGNG INDUSTRY; U.S.A.; DA. 1977; VOL. 99; NO 2; PP. 410-418; BIBL. 10 REF.Article

THE ROLE OF LUBRICANTS IN MACHINING.WILLIAMS JA; TABOR D.1977; WEAR; NETHERL.; DA. 1977; VOL. 43; NO 3; PP. 275-292; BIBL. 17 REF.Article

AN INVESTIGATION OF BUILT-UP EDGE FORMATION IN THE MACHINING OF ALUMINIUM.BAO H; STEVENSON MG.1976; INTERNATION. J. MACH. TOOL DESIGN RES.; U.S.A.; DA. 1976; VOL. 16; NO 3; PP. 165-178; BIBL. 20 REF.Article

BERECHNUNG VON RATTERSTABILITAETSDIAGRAMMEN AUFGRUND VIBRATIONSFREIER ZERSPANUNGSVERSUCHE = CALCUL DU DIAGRAMME DE STABILITE AU BROUTEMENT A PARTIR D'ESSAIS EN COUPE NON VIBRANTECHIAPPULINI R.1974; WERKSTATT U. BETRIEB; DTSCH.; DA. 1974; VOL. 107; NO 9; PP. 551-555; ABS. ANGL. FRArticle

A NEW MODEL FOR INITIAL CHIP CURL IN CONTINUOUS CUTTINGHORNE JG.1978; INTERNATION. J. MECH. SCI.; GBR; DA. 1978; VOL. 20; NO 11; PP. 739-745; BIBL. 10 REF.Article

CONSIDERATIONS SUR LES CARACTERISTIQUES DE LA SURFACE USINEE DE L'ALUMINIUM LORS DE LA COUPE ORTHOGONALE INSTATIONNAIREZAIMA S; KAMO T.1977; J. JAP. INST. LIGHT METALS; JAP.; DA. 1977; VOL. 27; NO 1; PP. 11-18; ABS. ANGL.; BIBL. 4 REF.Article

A MODEL FOR ORTHOGONAL MACHINING BASED ON THE THEORY OF STRESS SINGULARITIES.ROTH RN.1977; INTERNATION. J. MACH. TOOL DESIGN RES.; U.S.A.; DA. 1977; VOL. 17; NO 2; PP. 117-125; BIBL. 8 REF.Article

RESEARCH NOTE: THE INFLUENCE OF SURFACE PREPARATION ON MACHINING FORCES AND CHIP GEOMETRYWOODWARD RL.1976; J. MECH. ENGNG SCI.; G.B.; DA. 1976; VOL. 18; NO 3; PP. 159-160; BIBL. 7 REF.Article

ON CUTTING WITH INTERNALLY COOLED CUTTING TOOL. COOLING EFFECT ON CUTTING MECHANISMOKAMOTO S; DOI M.1975; BULL. JAP. SOC. PRECIS. ENGNG; JAP.; DA. 1975; VOL. 9; NO 1; PP. 13-18; BIBL. 9 REF.Article

ON THE MICRO-ASPERITIES OF MACHINED SURFACE IN HIGH SPEED METAL CUTTINGNISHINA K.1974; BULL. JAP. SOC. PRECIS. ENGNG; JAP.; DA. 1974; VOL. 8; NO 4; PP. 159-160; BIBL. 3 REF.Article